How to switch Huawei E303 to modem mode (Windows) Pre-requisites: An existing installation of Huawei Mobile Partner or a recent version of the standalone Huawei drivers. Kenny rogers blaze of glory free mp3 download. Unlock Code of E303; How to Unlock E303? Firmware of E303; Huawei E303 Drivers; Huawei E303 Software; E303 sub-models; E303 by Network Provider.
How to switch Huawei E303 to modem mode (Windows) Pre-requisites: An existing installation of or a recent version of the standalone Huawei drivers. After the initial installation from the virtual CD-ROM, when the modem is plugged in it appears in XP's device manager as a 'Windows Mobile-based Internet Sharing Device' under Network adapters. The name is slightly different in Windows 7 (can someone please post a screenshot or the name?). The hardware ID of this device is: USB Vid_12d1&Pid_14db&Rev_0102. Windows does not know which driver to install for these devices, but fortunately the driver is provided by Mobile Partner and just needs slight modification.
This procedure only needs to be performed once. Assuming a default installation of Mobile Partner, locate the file ewser2k.inf and open it in Notepad or Wordpad.
On English systems the file will be located at C: Program Files Mobile Partner Driver Driver X86 on 32-bit systems and C: Program Files (x86) Mobile Partner Driver Driver X64 on 64-bit systems. Near the start of the file you should see a section named [QcomSerialPort]. We need to add the following lines. Dss player pro 5 serial number. [QcomSerialPort].%QcomDevice01% = QportInstall01, USB VID_12d1&PID_143E&MI_02 [b]%QcomDevice01% = QportInstall01, USB VID_12d1&PID_1442&MI_00%QcomDevice00% = QportInstall00, USB VID_12d1&PID_1442&MI_01[/b]%QcomDevice01% = QportInstall01, USB VID_12d1&PID_1448&MI_01Now right-click on each unknown device in turn and tell Windows you will select the driver and point at the location where you found ewser2k.inf as above. After doing this, the devices should now appear as a 3G PC UI Interface and a 3G Application Interface under Ports. Hi I would also like to get my E303 into dailup mode my hardware version is CH2E303SM same as yours ginggs but my software is older then yours 22.157.39.00.00 I have tried the updates on the HLINK page but it shows as up to date. I followed your walk through and almost everything works the same there is only 1 part that I might be doing wrong when I open the terminal and connect to com5 my 3G PC UI Interface it show data being received on com5 is that correct.
I still went ahead and added the AT commands it displays in the receive box but does not do anything to the modem and then when I remove and reinsert the dongle it goes back to default. I think there might be something I am doing wrong. Will adding the AT commands with the terminal make the setting permanent or will it still reset after removal. Hi thx for the reply the terminal command does not respond with OK or ERROR just show the AT command. I have tried MDMA with command /hwstorage:0 and it does work. Let me explain what I want to do I have a 3g router'TL-MR3420' and I want to use Vodacom's unrestricted APN but if the E303 connects on the router it does not allow me to do port forwarding when I look on the router what the ip from the internet is it shows an local network ip 192.168.1.1 that the e303 provides but the e303 does not seems to send somekind of DMZ to that ip so no Port Fowarding but the internet works. I also have a e353 and that is always in modem mode so when I used that on the 3g router it connects with the internet ip showing on the router's status and then I can do Port Forwarding.
Thx in advance for you help any info will appreciated. Hey Guys okay now this is all good and well, I have a E3131 Huawei Modem. I did the following: I pasted in my browser and my Hlink Disconnected, then saw the unidentified HUAWEI devices in Device Manager. Now whats the Code to put into the ewser2k.inf file for the E3131? I have also already downloaded Terminal app. I basically only now need to edit the ewser2k.inf file with the code and then send the other code (AT^U2DIAG=0 AT+CFUN=4 AT+CFUN=6 to the correct comport? Can you guys please help I am not very clued up with these kind of stuff.
Greatly appreciated. What would the FULL code be and where would you insert it between what lines? And maybe a screenshot of where to do what in Terminal Window would be great Example of full code:%QcomDevice01% = QportInstall01, USB VID_12d1&PID_143E&MI_02%QcomDevice01% = QportInstall01, USB VID_12d1&PID_1442&MI_00%QcomDevice00% = QportInstall00, USB VID_12d1&PID_1442&MI_01%QcomDevice01% = QportInstall01, USB VID_12d1&PID_1448&MI_01 Sorry but please be more specific when replying since I am a noob at these stuff.